Short answer — Specify hotel upholstery fabric by where it will be used, how it will be cleaned and which performance tests apply. An abrasion number is one screening measure. It does not predict service life on its own.
Start with the exact hotel location
A fabric that works on a guestroom lounge chair may face a different risk profile on lobby seating, a restaurant banquette or an outdoor cushion. Before comparing samples, record the furniture item, room or zone, expected traffic, exposure to food or drink, cleaning method, sunlight and whether children, luggage or frequent reconfiguration will affect the surface.
This end-use description gives designers, contractors and suppliers a common basis for comparison. It also prevents a very high abrasion result from being used to compensate for a fabric that is difficult to clean, unstable in colour or unsuitable for the upholstery construction.
Compare abrasion results within the same test method
Martindale and Wyzenbeek are different laboratory methods. Martindale results are normally reported in cycles, while Wyzenbeek results are reported in double rubs. There is no reliable conversion between them, so two fabrics should be compared using the same method, pressure and test standard.
As a useful North American reference, the Association for Contract Textiles lists 20,000 Martindale cycles or 15,000 Wyzenbeek double rubs for commercial low-traffic and private spaces, and 40,000 Martindale cycles or 30,000 Wyzenbeek double rubs for commercial high-traffic public spaces. These are voluntary guidelines, not a substitute for the hotel brand standard, project specification or applicable code.
A result above the project requirement is not automatically a better purchase. ACT notes that a fabric with twice the abrasion result does not mean twice the service life. Cleaning, maintenance, physical abuse, edge wear and the suitability of the application all influence performance.
Build a specification that suppliers can quote consistently
- End use — item code, room or public area, indoor or outdoor use and expected traffic.
- Material — fibre content, construction, backing and any finish or coating identified by the textile supplier.
- Colour — supplier colour reference plus an approved physical cutting or control sample.
- Abrasion — required test method, standard, pressure where relevant and minimum result.
- Appearance retention — pilling, seam slippage and dimensional stability where the application requires them.
- Colour performance — colourfastness to light and crocking requirements appropriate to the location.
- Cleanability — approved agents, stain-removal method and any restrictions on bleach or solvents.
- Compliance — the fire, chemical and accessibility requirements stated by the project team for the destination and application.
- Commercial information — usable width, repeat, direction, minimum order, lead time, dye-lot control and allowance for waste.
If the upholstery is customer-supplied material, agree who checks the usable width, defects and quantity before cutting. If the furniture supplier provides the fabric, ask the quotation to identify the exact textile reference and the assumptions used for consumption.
Review the fabric on the actual furniture sample
A flat swatch cannot show how the textile behaves around curves, seams, piping, tufting or high-contact edges. Apply the proposed fabric to a production-representative sample when the item is custom, visually important or technically difficult. Check pattern direction, seam placement, stretch, surface marking, colour under the intended lighting and how the material responds to the approved cleaning method.
Record the approved sample, textile code and drawing revision together. The signed reference should be available to production and quality control. PROSFFE’s hotel furniture sample approval guide explains how to connect the prototype, finish samples and room conditions before release.
Match the maintenance plan to the specification
Before approval, give the operator the supplier’s current care instructions. Confirm routine vacuuming, spot-cleaning steps, drying time and which products are prohibited. A fabric can pass an abrasion test and still fail early if the cleaning chemistry damages its coating, removes colour or leaves soil-attracting residue.
Hotel upholstery specification checklist
- Identify the furniture item and exact location.
- Define traffic, spill, sunlight and cleaning conditions.
- Choose one abrasion method and state the test standard.
- Add relevant physical, colour and cleanability requirements.
- Confirm destination-specific project compliance with the responsible consultant.
- Approve a physical cutting and, where needed, an upholstered sample.
- Freeze the textile code, colour, dye lot and drawing revision before production.
- Issue care instructions to the operator at handover.
Frequently asked questions
Is a higher Martindale result always better for hotel seating?
No. Once the fabric meets the appropriate project requirement, evaluate cleanability, appearance retention, construction and application. A higher result does not prove a proportionally longer service life.
Can Martindale cycles be converted into Wyzenbeek double rubs?
No reliable conversion should be used for specification. Compare fabrics tested to the same method and report the method with the result.
Should guestrooms and lobby seating use the same requirement?
Not automatically. The team should classify each application by traffic, cleaning and operational risk, then apply the hotel brand standard and project requirements for that location.
Planning custom hotel seating? Send PROSFFE your furniture schedule, upholstery references and room plans so we can review the sampling and manufacturing brief.
